Multipurpose steering wheel, universal display
Buttons on a multipurpose steering wheel depending on a complete set of your car the call on the universal display of below-mentioned systems, management by them and installation of their parameters can be made:
1 — the run Measuring instrument from the moment of dumping and the counter of the general run
Index of temperature of cooling liquid
Digital indication of speed
Indicator of term of approach planned THAT (ASSYST)
Indication of level of motive oil
2 — Audio systems
Radio receiver
CD player
Cassette sound board
3 — the Navigation system
4 — Memory of display of faults
5 — Individual installation
6 — the Travelling computer
From the moment of start
From the moment of dumping
Course stock
7 — Phone Or press the button until the required system is displayed. With each new pressing of the button the following system is displayed.
In some systems additional indications can be caused by pressing of the button or.
|
|
Indications on the universal display, depending on installation, are made in the German, English, French, Italian or Spanish languages. Switching to other language - see the INSTRUMENT CLUSTER (CONTROL PANEL) menu of the Individual Installation system of the menu of the TEHT installation (TEXT LANGUAGE). |
Irrespective of the established language, on models with radio receivers of the Audio system 10, Audio 10 CD or Audio 30 APS indications of audio systems (the radio receiver, the CD player, a cassette sound board), and also indications on phone appear in English.
1 — the Universal display
2 — the Multipurpose steering wheel
Turn a key in the ignition switch in situation 1 or 2.
Press the button:
3 — the Following system
4 — the Previous system
5 — the Following indication within system
6 — the Previous indication within system
7 — Increase in loudness
8 — Reduction of loudness
9 — a Set of a phone number, reception of the arriving telephone conversation
10 — the End of telephone conversation, refusal of reception of the arriving telephone conversation
11 A sound signal on a soft cover
Or press the button until the required system is displayed.
With each new pressing of the button the following system is displayed.
In some systems additional indications can be caused by pressing of the button or.
Run measuring instruments, term indicators THAT and indexes - speeds, temperatures of OZh and level of oil
1 — Zeroing of the measuring instrument of a run from the moment of dumping (see below)
2 — the Index of temperature of cooling liquid (see below)
3 — Digital indication of speed - if in the Individual Installation system in the INSTRUMENT CLUSTERS (CONTROL PANEL) menu, in the menu of the SELECT DISPLAY installation (the INDICATION CHOICE), is chosen the SPEED installation (SPEED) (see below)
Indication of temperature of external air 1 - if in the Individual Installation system, in the INSTRUMENT CLUSTERS (CONTROL PANEL) menu, in the menu of the SELECT DISPLAY installation (the INDICATION CHOICE), is chosen the OUTSIDE TEMPERATURE installation (TEMPERATURE of EXTERNAL AIR) (see below)
4 — the Indicator of term of approach planned THAT (ASSYST) (The head Routine maintenance)
5 — Indication of level of motive oil (The head Routine maintenance)
1) Except for Great Britain
Or press the button until there is an indication of the measuring instrument of a run from the moment of dumping and the counter of the general run (1).
Or press the button until there is a required indication (2, 3, 4, 5, 1).
Pressing of the button or displays the following or previous system.
Audio systems
Depending on the switched-on audio system the corresponding indication on the display appears.
The radio receiver - indication for audiodevices and the COMAND system
1 — Any audio system is not switched on
2 — the radio receiver Is switched on
3 — the strip of frequencies and, if necessary, in addition number of a cell of memory Is established
4 — the Name of the adjusted radio station or its frequency
5 — "SP" (memory) - if in the Individual Installation system, in the VEHICLE menu (CAR), in the menu of the PRESS BUTTON IN AUDIO MODE installation (PRESSING of the BUTTON IN AUDIO MODE), is chosen the MEMORY installation (MEMORY), But NOT "STATION SEARCH" (SEARCH of RADIO STATION)
Turn on the radio receiver (separate "Operation manual").
Or press the button until indication appears (2).
Or press the button until the required radio station or frequency is displayed.
The button or the frequency of radio station or the remembered radio station can be chosen. It depends on installation in the menu of the installations "PRESS BUTTON" "IN AUDIO MODE" (PRESSING of the BUTTON IN the AUDIO MODE) (see. "Individual installation", VEHICLE menu (CAR)
Pressing of the button or displays the following or previous system.
The CD player - indication for audiodevices
The CD player - indication for the COMAND system
1 — Any audio system is not switched on
2 — the CD player is switched on
3 — At a CD changer number of the lost compact disk is displayed
4 — Number of the piece of music
Turn on the CD player (separate "Operation manual").
Or press the button until indication appears (2).
Or press the button until the required number of the piece of music (4) is displayed.
Pressing of the button or displays the following or previous system.
The cassette tape recorder - indication for Audio 10
1 — Any audio system is not switched on
2 — the cassette sound board Is included
3 — the Lost party
Include a cassette sound board (separate "Operation manual").
Or press the button until indication appears (2).
Press the button - the rewinding is made prior to the beginning of the following piece of music.
Press the button - the rewinding is made prior to the beginning of the lost piece of music.
Pressing of the button or displays the following or previous system.
The navigation system - indication for Audio 30 APS and the COMAND systems
1 — the Navigation system is switched off
2 — the Navigation system is switched on, but maintenance of the purpose is not made
3 — the Navigation system is switched on, and maintenance of the purpose is activated
Or press the button until the required system is displayed.
(The navigation system - separate "Operation manual" on the COMAND systems (Cockpit Management and Data System) or Audio 30 APS).
Pressing of the button or displays the following or previous system.
Memory of display of faults
1 — Malfunctions are absent
2 — Number of malfunctions
3 — In memory of display of faults malfunctions are remembered
Or press the button until memory of display of faults is displayed.
If there is an indication (2), press the button or. After that consecutive display of faults is made.
(The warning system and the alarm system of malfunctions - see the Section Precautionary alarm and control lamps, and also messages of the information display on the registered malfunctions)
Upon completion of indication of all malfunctions indication appears (2) again.
If malfunctions arose during the movement, indication (2) appears once again when the key in the switch of ignition turns in situation 0 or is taken out. It is possible to cause repeated display of faults on the control panel pressing of the button of dumping of indications (The section the Control panel).
When turning a key in the ignition switch in situation 1 or 2 memory of display of faults is dumped.
If malfunctions arose repeatedly, then they are again displayed in memory of display of faults.
Pressing of the button or displays the following or previous system.
Individual installation
1 — Basic indication of individual installation
2 — "SETTING" (INSTALLATION) - in this additional menu it is possible to open the required menu: "INSTRUMENT CLUSTER" (CONTROL PANEL) (see below)
"LIGHTING" (LIGHTING) (see below)
"VEHICLE" (CAR) (see below)
"HEATER" (HEATING) (see below)
"CONVENIENCE" (COMFORTABLE MANAGEMENT) (see below)
Each menu has in turn additional submenu - the menu of installations. In them can be then the corresponding installations are made.
3 — Dumping of the additional SETTINGS menu (INSTALLATION), request for confirmation (see below)
4 — the Confirming message
Or press the button until basic indication of the Individual Installation system appears (1).
Or press the button until the additional SETTINGS menu (INSTALLATIONS) is displayed (2)
Or press the button until the required menu is noted:
"INSTRUMENT CLUSTER" (CONTROL PANEL) (see below)
"LIGHTING" (LIGHTING)
"VEHICLE" (CAR) (see below)
"HEATER" (HEATING) (see below)
"CONVENIENCE" (COMFORTABLE MANAGEMENT) (see below)
Pressing of the button or displays the following or previous system.
Dumping of the SETTINGS menu (INSTALLATION) (2):
If you make dumping of the SETTINGS menu (INSTALLATION) (2), then all installations become factory installation again.
Cause basic indication of the Individual Installation (1) or SETTINGS system (INSTALLATION) (2)
Press the button of dumping of indications on the control panel (The section the Control panel) and hold pressed about 3 seconds. There is an indication (3).
Repeatedly press the button of dumping of indications. For confirmation indication appears (4).
If the button of dumping of indications is not pressed, then approximately in 5 seconds basic indication of the Individual Installation system appears (1). In this case menus of installations are not dropped.
|
|
When dumping indications during the movement for safety reasons in the LIGHTING menu (LIGHTING) And "VEHICLE" (CAR) not all menus of installations are dropped (see below). |
CONTROL PANEL menu
1 — Basic indication of individual installation
2 — "SETTINGS" (INSTALLATION) - the additional menu for the choice of the menu
3 — "SET TIME" (INSTALLATION OF TIME) "HOURS" (HOURS) 1
4 — "SET TIME" (INSTALLATION OF TIME) OF "MINUTES" (MINUTE)
5 — "12/24 O'CLOCK" - the 12th or 24-hour indication
6 — "TEMP. INDICATOR" (TEMPERATURE INDICATOR) - the established unit of measure is displayed on the indicator of temperature of external air on the control panel, and on models with the automated air conditioner with comfortable management also on the display of this system
7 — "DISPLAY VALUES IN" (VALUES ON the DISPLAY B) - installation is valid for all indications on the universal display (not for a speedometer)
8 — "TEHT" (TEXT LANGUAGE) - installation of language for indication on the universal display
9 — "SELECT DISPLAY" (the CHOICE of the INDICATOR) 2 - the chosen SPEED DISP. option (SPEED) or "OUTSIDE TEMPERATURE" (TEMPERATURE of EXTERNAL AIR) is constantly displayed on the universal display.
"SPEED DISP." (SPEED), for example, can be used for additional indication of speed of the movement in miles if to the menu of installations (7) "SPEEDOMETER" (SPEEDOMETER) it is established on "MILES" (MILES)
10 — Dumping of the CONTROL PANEL menu, request for confirmation (see below)
11 — the Confirming message
|
|
On the block diagram the example of possible installation is presented. |
1 Only models without the COMAND system or without Audio 30 APS. (The COMAND or Audio system 30 APS - separate "Operation manual").
2 Except for Great Britain.
Or press the button until basic indication of the Individual Installation system appears (1).
Or press the button until the additional SETTINGS menu (INSTALLATIONS) is displayed (2)
Or press the button until the INSTRUMENT CLUSTER (CONTROL PANEL) menu is noted.
Or press the button until the required menu of installation (2-9) is displayed.
In the menu of installations (3, 4) or time is determined by pressing the button, and in the menu of installations (5-9) the required installation is chosen.
The chosen installation is noted.
The made installations are remembered and immediately carried out.
After passing of all menus of installations basic indication of the Individual Installation system is again displayed (1).
Pressing of the button or displays the following or previous system.
Dumping of the INSTRUMENT CLUSTER menu (CONTROL PANEL) (5-9) on factory installation:
Cause one of the menu of installations (5-9).
The button of dumping of indications on the control panel (The section the Control panel), press and hold pressed about 3 seconds. There is an indication (10).
Repeatedly press the button of dumping of indications. For confirmation indication appears (11).
If the button of dumping of indications is not pressed, then approximately in 5 seconds the additional SETTINGS menu (INSTALLATIONS) is displayed (2). In this case menus of installations are not dropped.
LIGHTING menu
1 — Basic indication of individual installation
2 — "SETTINGS" (INSTALLATION) - the additional menu for the choice of the menu
3 — "LIGHT CIRCUIT HEADLAMP MODE" (SWITCHING SVETA FAR) (Undressed Switches)
4 — "LOCATOR LIGHTING" (LIGHTING FOR ORIENTATION) (Undressed Switches)
5 — "HEADLAMPS DELAYED SWITCH-OFF" (the SLOWED-DOWN SWITCHING OFF SVETA FAR (Undressed Switches)
6 — "INT. ILLUMINATION DELAYED SWITCH-OFF" (SHUTDOWN of INTERNAL LIGHTING WITH ENDURANCE of TIME) (Undressed Window regulators, the roof hatch)
7 — Dumping of the LIGHTING menu (LIGHTING), request for confirmation (see below)
8 — the Confirming message
|
|
On the block diagram the example of possible installation is given above. |
Or press the button until basic indication of the Individual Installation system appears (1).
Or press the button until the additional SETTINGS menu (INSTALLATIONS) is displayed (2).
Or press the button until the LIGHTING menu (LIGHTING) is noted.
Or press the button until the required menu of installation (2-6) is displayed.
In the menu of installations (3-6) installation is chosen pressing of the button or. The chosen installation is noted.
The made installations are remembered and immediately carried out.
After passing of all menus of installations basic indication of the Individual Installation system is again displayed (1).
Pressing of the button or displays the following or previous system.
Dumping of the LIGHTING (LIGHTING) (3-6) menu on factory installation:
Cause one of the menu of installations (3-6).
Press the button of dumping of indications on the control panel (The section the Control panel) and hold pressed about 3 seconds. There is an indication (7).
Repeatedly press the button of dumping of indications. For confirmation indication appears (8).
If the button of dumping of indications is not pressed, then approximately in 5 seconds the additional SETTINGS menu (INSTALLATIONS) is displayed (2). In this case menus of installations are not dropped.
|
|
When dumping indications during the movement for reasons of safety of the menu of the HEADLAMP MODE installation (SWITCHING SVETA FAR) it is not dumped. There is a message of "LIGHTING CANNOT BE COMPLETELY RESET TO FACTORY SETTINGS WHILE DRIVING" (LIGHTING during the MOVEMENT is not DUMPED COMPLETELY ON FACTORY INSTALLATION). |
CAR menu
1 — Basic indication of individual installation
2 — "SETTINGS" (INSTALLATION) - the additional menu for the choice of the menu
3 — "SPEED LIMIT (WINTER TYRES)" (RESTRICTION of SPEED, the TIRE WITH the WINTER DRAWING of the PROTECTOR)" 1, - the constant limiter of speed (The section Driving and auxiliary systems).
Possibility of the choice at models with the petrol engine: "Off", "240 km/h" to "160 km/h" in steps on 10 km/h.
Possibility of the choice at models with the diesel engine: "Off", "210 km/h", "190 km/h", "160 km/h".
4 — "PRESS BUTTON IN AUDIO MODE" (PRESSING of the BUTTON IN the AUDIO MODE) - installation of the radio receiver
"STACION SEARCH" (SEARCH of RADIO STATION) - the button or is chosen frequency
"MEMORY" (MEMORY) - the button or is chosen the remembered radio station
5 — "AUTOMATIC DOOR CLOCK" (AUTOMATIC LOCKING of DOORS) (Undressed Locks, keys and locks. Uniform lock)
6 — Dumping of the CAR menu, request for confirmation (see below)
7 The confirming message
|
|
On the block diagram the example of possible installation is given above. |
Or press the button until basic indication of the Individual Installation system appears (1).
Or press the button until the additional SETTINGS menu (INSTALLATIONS) is displayed (2).
Or press the button until the VEHICLE menu (CAR) is noted.
Or press the button until the required menu of installation (2-5) is displayed.
In the menu of installations (3-5) the required installation is chosen pressing of the button or. The chosen installation is noted. The made installations are remembered and immediately carried out.
After passing of all menus of installations basic indication of the Individual Installation system is again displayed (1).
Pressing of the button or displays the following or previous system.
Dumping of the VEHICLE menu (CAR) (3-5) on factory installation:
Cause one of the menu of installations (3-5).
Press the button of dumping of indications on the control panel and hold pressed about 3 seconds. There is an indication (6).
Repeatedly press the button of dumping of indications. For confirmation indication appears (7).
If the button of dumping of indications is not pressed, then approximately in 5 seconds the additional SETTINGS menu (INSTALLATIONS) is displayed (2). In this case menus of installations are not dropped.
|
|
When dumping indications during the movement for reasons of safety of the menu of the SPEED LIMIT (WINTER TYRES) installation (RESTRICTION of SPEED, the TIRE WITH the WINTER DRAWING of the PROTECTOR) it is not dumped. There is a message "VEHICLE CANNOT BE COMPLETELY RESET TO FACTORY SETTINGS WHILE DRIVING!" (The CAR during the MOVEMENT is not DUMPED COMPLETELY ON FACTORY INSTALLATION). |
Heating menu
1 — Basic indication of individual installation
2 — "SETTINGS" (INSTALLATION) - the additional menu for the choice of the menu
3 — "AUXILIARY HEATING" (THE INDEPENDENT HEATER)
4 — "AUXILIARY HEATING SWITCH-ON TIME 1 HOURS" (THE INDEPENDENT HEATER, TIME OF INCLUSION 1 - HOURS) 1, 2
5 — "AUXILIARY HEATING SWITCH-ON TIME 1 MINUTS" (THE INDEPENDENT HEATER, TIME OF INCLUSION 1 - MINUTES)
6 — "HEATER BOOSTER" (THE ADDITIONAL HEATING DEVICE) 3
7 — Dumping of the HEATER menu (HEATING), request for confirmation
8 — the Confirming message
|
|
On the block diagram the example of possible installation is given above. |
1) Only models with an independent heater
2) Appears only if in the menu of installations (3) "AUXILIARY HEATING" (the INDEPENDENT HEATER) "TIME" (TIME) is chosen.
3) Only models with the diesel engine.
Or press the button until basic indication of the Individual Installation system appears (1).
Or press the button until the additional SETTINGS menu (INSTALLATIONS) is displayed (2).
Or press the button until the HEATING menu (HEATING) is noted.
Or press the button until the required menu of installations (2-6) is displayed.
In the menu of installations (4, 5) or time is determined by pressing the button, and in the menu of installation (3, 6) the required installation is chosen. The chosen installation is noted.
The made installations are remembered and immediately carried out.
After passing of all menus of installations basic indication of the Individual Installation system is again displayed (1).
Pressing of the button or displays the following or previous system.
Dumping of the HEATING (HEATING) (3-6) menu on factory installation.
Cause one of the menu of installations (3-6).
Press the button of dumping of indications on the control panel (The section the Control panel) and hold pressed about 3 seconds. There is an indication (7).
Repeatedly press the button of dumping of indications. For confirmation indication appears (8).
If the button of dumping of indications is not pressed, then approximately in 5 seconds the additional SETTINGS menu (INSTALLATIONS) is displayed (2). In this case menus of installations are not dropped.
Menu of the INDEPENDENT HEATER installation
Do not include an independent heater at gas stations and in the enclosed space without extract (for example, in garages).
Installation and the choice of the required inclusion time
Open the menu of installation (3) "AUXILIARY HEATING" (the INDEPENDENT HEATER).
Pressing the button or note, for example, "TIME 1" (TIME 1).
Open the menu of installation (4) "AUXILIARY HEATING" (the INDEPENDENT HEATER) "SWITCH-ON TIME 1 HOURS" (TIME of INCLUSION 1, HOURS) and pressing of the button or establish the required hours.
Open the menu of installation (5) "AUXILIARY HEATING" (the INDEPENDENT HEATER) "SWITCH-ON TIME 1 MINUTES" (TIME of INCLUSION 1, MINUTES) and pressing of the button or establish the required minutes.
Time of inclusion of an independent heater is established and chosen.
The choice of the required inclusion time:
Open the menu of installation (3) "AUXILIARY HEATING" (the INDEPENDENT HEATER).
Pressing the button or note the required TIME menu (TIME).
Time of inclusion of an independent heater is chosen.
The Comfortable Management menu (models with memory function)
1 — Basic indication of individual installation
2 — "SETTINGS" (INSTALLATION) - the additional menu for the choice of the menu
3 — "EASY-ENTRY FEATURE ACTIVATE" (to ACTIVATE SYSTEM of ASSISTANCE to LANDING) (The section Simplification of Landing and Disembarkation from the car)
— "SETTINGS" (INSTALLATION) "KEY-DEPENDENT" (DEPENDING ON the KEY) - if the ON installation is chosen 4 (INCL.), all installations made in the menu of the Individual Installation system can be entered into memory depending on a key. (Memory function - see the Section Memory of Provisions of Seats, a steering wheel and external mirrors)
5 — "MIRROR SETTING WHEN PARKING" (ADJUSTMENT of PROVISION of MIRRORS AT the PARKING) (Undressed the Steering wheel, rear-view mirrors)
6 — Dumping of the CONVENIENCE menu (COMFORTABLE MANAGEMENT), request for confirmation (see below)
7 — the Confirming message
|
|
On the block diagram the example of possible installation is given above. |
Or press the button until basic indication of the Individual Installation system appears (1).
Or press the button until the additional SETTINGS menu (INSTALLATIONS) is displayed (2).
Or press the button until the CONVENIENCE menu (COMFORTABLE MANAGEMENT) is noted.
Or press the button until the required menu of installation (2-5) is displayed.
In the menu of installations (3-5) the required installation is chosen pressing of the button or. The chosen installation is noted. The made installations are remembered and immediately carried out.
After passing of all menus of installations basic indication of the Individual Installation system is again displayed (1).
Pressing of the button or displays the following or previous system.
Dumping of the CONVENIENCE menu (COMFORTABLE MANAGEMENT) (3-5) on factory installation:
Cause one of the menu of installations (3-5).
Press the button of dumping of indications on the control panel (The section the Control panel) and hold pressed about 3 seconds. There is an indication (6).
Repeatedly press the button of dumping of indications. For confirmation indication appears (7).
If the button of dumping of indications is not pressed, then approximately in 5 seconds the additional SETTINGS menu (INSTALLATIONS) is displayed (2). In this case menus of installation are not dropped.
Traveling computer
1 — "AFTER START" – the run measuring instrument since launch
2 — "AFTER RESET" - the run measuring instrument from the moment of dumping
3 — "RANGE" (the COURSE STOCK) - indication of availability of fuel in the fuel tank with the approximate indication of a distance which can be passed with the available fuel reserve
4 — the Run since launch or dumping into km of "AFTER START" or "AFTER RESET"
5 — Time since launch or dumping of "AFTER START" or "AFTER RESET"
6 — Average speed since launch or dumping of "AFTER START" or "AFTER RESET"
7 — Average fuel consumption since launch or dumping of "AFTER START" or "AFTER RESET"
Or press the button until indication appears (1, 2 or 3).
Or press the button until indication of the measuring instrument of a run since launch of "AFTER START" (1), the run measuring instrument from the moment of dumping of "AFTER RESET" (2) or indication of a reserve of fuel (3) appears.
Pressing of the button or displays the following or previous system.
|
|
By a repeated call of the traveling computer indication of the measuring instrument since launch of "AFTER START" (1) always appears. |
Dumping of the measuring instrument of a run since launch "AFTER START" (1) or the measuring instrument of a run from the moment of dumping of "AFTER RESET" (2)
The button or cause the corresponding indication (1 or 2) and, having pressed the button of dumping of indications on the control panel (The section the Control panel), to wait for dumping of indications on "0".
|
|
When turning a key in the ignition switch in situation 0 or its taking out approximately in 4 hours dumping of the measuring instrument of a run since launch of "AFTER START" (1) is automatically made if during this time the key does not turn in situation 1 or 2 again. |
Phone
The telephone directory - indication for audiodevices
The telephone directory - indication for the COMAND system
1 — Phone is switched off.
2 — Input of the PIN code (a personal identification code) of the SIM card - the separate "Operation manual on phone" or respectively "Operation manual" on the Linguatronic system
3 — search of the corresponding telephone network Is run
4 — Phone is ready for operation. The relevant provider of GSM network is displayed
5 — Now the car out of the range of transfer or reception
6 — the telephone directory remembered on the phone card or in phone Is read out. Duration - about 30 seconds
7 — the surname Chosen from the telephone directory
8 — Number of the chosen subscriber, process of set of number begins
9 — Process of set of number is finished, and the surname is displayed. Indication remains during all telephone conversation
10 — signal Force - on the right on the display on models with audiodevices: the number is higher, the accepted signal of GSM network is stronger
Signal force - at the left on the display on models with the COMAND system: the more it is displayed strips, the accepted signal of GSM network is stronger
11 — Number of a cell of memory
12 — Indication of duration of a conversation
Phone and the audiodevice or the COMAND system have to be switched on.
Or press the button until the relevant provider of GSM (4) network appears. At emergence of indication (2) at first enter the PIN code (the separate "Operation manual on phone" or respectively "The operation manual on the Linguatronic system).
Press the button or, the telephone directory "is glanced over" alphabetically forward or back. The corresponding chosen surname appears on the display.
Models with the Audio radio receiver of 10 CDs or the Comand system:
If the button or is pressed longer than one second, then the accelerated "scrolling" of the telephone directory is made.
|
|
If you decided not to call, press the button. Process is interrupted, and indication appears (4). |
Press the button if on the display the surname of the required subscriber is displayed (7). Phone number is dialed (8).
If process of set of number is finished, the surname is displayed (9). Indication (9) remains during all telephone conversation.
Press the button, telephone conversation comes to an end, indication appears (4).
Pressing of the button or displays the following or previous system.
Repeated call of the subscriber - indication for audiodevices
Repeated call of the subscriber - indication for the COMAND system
1 — Phone is ready for operation. The relevant provider of GSM network is displayed
2 — Number or a surname in memory of a repeated call of the subscriber
3 — Number in memory of a repeated call of the subscriber - is begun process of set of number
4 — Process of set of number is finished, and the surname of the subscriber remembered in the telephone directory or the dialed number is displayed if the surname of the subscriber is not remembered. Indication remains during all telephone conversation
5 — signal Force - on the right on the display on models with audiodevices:
the number is higher, the accepted signal of GSM network is stronger
Signal force - at the left on the display on models with the COMAND system:
the more it is displayed strips, the accepted signal of GSM network is stronger
6 — Number of a cell of memory of the COMAND system: the last are remembered 10 dialed numbers.
L0, the last dialed number,
L1-L9, the previous dialed numbers
Number of a cell of memory of audiodevices:
the last are remembered 9 dialed numbers,
LO, the last dialed number,
L1-L9, the previous dialed numbers
7 — Indication of duration of a conversation
Phone and the audiodevice or the COMAND system have to be switched on.
Or press the button until the relevant provider of GSM (1) network appears.
Press the button - memory of a repeated call of the subscriber is activated, and the subscriber number dialed by the last is displayed.
Press the button or - memory of a repeated call of the subscriber "is glanced over" forward or back. The corresponding chosen number appears on the display.
|
|
If you decided not to call, press the button. Process is interrupted, and indication appears (1). |
Press the button if on the display (2) the required number or a surname of the required subscriber is displayed.
Phone number is dialed (3).
If process of set of number is finished, the surname (4) if it is remembered in the telephone directory is displayed; otherwise indication of a phone number remains. Indication remains during all telephone conversation.
Press the button, telephone conversation comes to an end, indication appears (1).
Pressing of the button or displays the following or previous system.
The arriving call
1 — you are called
2 — signal Force - on the right on the display on models with audiodevices:
the number is higher, the accepted signal of GSM network is stronger
Signal force - at the left on the display on models with the COMAND system:
the more it is displayed strips, the accepted signal of GSM network is stronger.
Phone is reported to be switched on.
Press the button and accept a call.
Press the button - the conversation comes to an end, indication with the corresponding telephone network appears.
|
|
If you do not want to accept the arrived call, press the button. |
Volume control
Press the button
increase in loudness.
reduction of loudness.
Only the loudness of the activated or chosen system can be regulated always.
Those are audio systems, phone, radio service of informing on a situation on roads, a speech conclusion of the navigation system and a speech conclusion of system of voice-activated control of "Linguatronic".
|
|
On models with the COMAND system the made volume control is remembered for each system separately. |
Index of temperature of cooling liquid
Turn a key in the ignition switch in situation 1 and 2;
If are not displayed the run measuring instrument from the moment of dumping and the counter of the general run, the button or on a multipurpose steering wheel press until indication appears (see above).
Or press the button until indication of temperature of cooling liquid appears.
During appropriate filling with antifreeze with anticorrosive additives the boiling point of cooling liquid in the pressure head cooling system is reached at a temperature about 130 °C.
At high temperatures of external air and at the movement in mountains temperature increase of cooling liquid until the end of a scale is allowed.
|