Mercedes C-Class

W203 since 2000 of release

Repair and operation of the car



Mercedes-Benz
+ Mercedes-Benz cars of class C (W-203)
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   - Leaving and external equipment of a body
      General information and security measures when carrying out body works
      Cleaning and leaving
      Repair of insignificant damages of body panels
      Repair of considerable damages of a body
      Damages of a windshield as a result of hit of stones
      Replacement of brushes of screen wipers
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of back glass
      Removal and installation of the lever of a screen wiper of a windshield
      Removal and installation of the lever of a back screen wiper
      Removal and installation of a catchment basin
      Removal and installation of a cowl
      Removal and installation of facing of a cowl
      Adjustment of a cowl
      Removal and installation of the lock of a cowl
      Drive cable detachment from the cowl lock
      Removal and installation of a lattice of a spoiler
      Removal and installation of a bumper
      Removal and installation of a rear bumper
      Removal and installation of a forward wing
      Removal and installation of a protective level on a wing
      Removal and installation of a protective level on a bumper
      Removal and installation of a protective level on a door
      Removal and installation of a forward loker covered
      Removal and installation of a back part of a loker of a wing
      Removal and installation of a forward door
      Adjustment of a door
      Removal and installation of forward facing of a door
      Removal and installation of a triangular slip
      Removal and installation of the external handle of a door
      Removal and installation of facing of an external rear-view mirror
      Removal and installation of an external mirror
      Removal and installation of glass of a mirror
      Removal and installation of a trunk lid
      Removal and installation of facing of a trunk lid
      Removal and installation of a clamp of the lock of a luggage carrier
      Removal and installation of the lock of a door of a back
      Removal and installation of the mechanism of the lock of a door of a back
      Removal and installation of the cylinder of the lock of a luggage carrier and door of a back
      Removal and installation of a door of a back
      Adjustment of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of a back spoiler
      Removal and installation of a cap of a cargo compartment
   + Equipment of salon
+ Onboard electric equipment






Removal and installation of a bumper

Removal

 PERFORMANCE ORDER

1. Mark with paint the provision of the corresponding forward wheel concerning a nave. It will allow to establish at assembly the balanced wheel in its former situation. Weaken bolts of fastening of a wheel before a car poddomkrachivaniye. Lift a forward part of the car, put it on supports and remove a forward wheel.
2. Lift a forward part of the car and establish on supports.

Lifting operation and installations of the car on supports is connected with danger! Therefore before carrying out operation study Poddomkrachivaniye's Section and towage of Introduction to the management.

3. Remove a forward loker, address appropriate section.

4. Turn out the lock screw (1) between a wing and a bumper. (4) – adjusting screw.

5. Disconnect by means of the screw-driver (2) a bracket (3) from a bumper and incline it to the center of the car.
6. Pull a bracket back and remove from a bumper.
7. Remove the sensor of temperature of external air, address the Section Removal and installation of the sensor of temperature of external air.
8. Disunite the socket of the left and right fog lights.
9. Disunite the socket of the assistant to the parking if it is established.

10. Turn out 2 screws of fastening (2) at fog lights on the right and at the left.

11. Open a cowl and turn out 2 screws (1) at headlights on the right and at the left.
12. Remove by means of the assistant a bumper from the car.


Installation

 PERFORMANCE ORDER

1. Establish by means of the assistant a bumper into place.
2. If it is necessary, adjust a gap by means of the screw (4). Value of a gap is given in Specifications.
3. Fix a bumper by 4 screws the moment of 4 Nanometers.
4. Insert a bracket between a wing and a bumper so that the collar of a bracket entered a guide on a bumper. Screw the lock screw.
5. Install the sensor of temperature of external air, address the Section Removal and installation of the sensor of temperature of external air.
6. Join the socket of foggy lamps.
7. Join the socket of the assistant to the parking if it is available.
8. Establish a loker of a wing, address the Section Removal and installation of a forward loker covered.
9. Establish into place a forward wheel so that the marks put at removal coincided. Previously grease with a thin layer of bearing lubricant the aligning wheel disk belt on a nave. Do not grease bolts of fastening of a wheel. Replace rusty bolts. Wrap bolts. Lower the car on wheels and tighten bolts cross-wise the moment of 110 Nanometers.
10. Attach a negative cable (-) to the rechargeable battery at the switched-off ignition. Establish into place a box of the filter of air of salon. Enter a code of the radio receiver and determine time on hours.
11. As soon as possible check adjustment of headlights for HUNDRED and, if necessary, adjust.