Mercedes C-Class

W203 since 2000 of release

Repair and operation of the car



Mercedes-Benz
+ Mercedes-Benz cars of class C (W-203)
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   - Leaving and external equipment of a body
      General information and security measures when carrying out body works
      Cleaning and leaving
      Repair of insignificant damages of body panels
      Repair of considerable damages of a body
      Damages of a windshield as a result of hit of stones
      Replacement of brushes of screen wipers
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of back glass
      Removal and installation of the lever of a screen wiper of a windshield
      Removal and installation of the lever of a back screen wiper
      Removal and installation of a catchment basin
      Removal and installation of a cowl
      Removal and installation of facing of a cowl
      Adjustment of a cowl
      Removal and installation of the lock of a cowl
      Drive cable detachment from the cowl lock
      Removal and installation of a lattice of a spoiler
      Removal and installation of a bumper
      Removal and installation of a rear bumper
      Removal and installation of a forward wing
      Removal and installation of a protective level on a wing
      Removal and installation of a protective level on a bumper
      Removal and installation of a protective level on a door
      Removal and installation of a forward loker covered
      Removal and installation of a back part of a loker of a wing
      Removal and installation of a forward door
      Adjustment of a door
      Removal and installation of forward facing of a door
      Removal and installation of a triangular slip
      Removal and installation of the external handle of a door
      Removal and installation of facing of an external rear-view mirror
      Removal and installation of an external mirror
      Removal and installation of glass of a mirror
      Removal and installation of a trunk lid
      Removal and installation of facing of a trunk lid
      Removal and installation of a clamp of the lock of a luggage carrier
      Removal and installation of the lock of a door of a back
      Removal and installation of the mechanism of the lock of a door of a back
      Removal and installation of the cylinder of the lock of a luggage carrier and door of a back
      Removal and installation of a door of a back
      Adjustment of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of a back spoiler
      Removal and installation of a cap of a cargo compartment
   + Equipment of salon
+ Onboard electric equipment




Removal and installation of a forward wing

Removal

 PERFORMANCE ORDER

1. Mark with paint the provision of the corresponding forward wheel concerning a nave. It will allow to establish at assembly the balanced wheel in its former situation. Weaken bolts of fastening of a wheel before a car poddomkrachivaniye. Lift a forward part of the car, put it on supports and remove a forward wheel.

Lifting operation and installations of the car on supports is connected with danger! Therefore before carrying out operation study Poddomkrachivaniye's Section and towage of Introduction to the management.

2. Remove a forward loker of a wing, address appropriate section.
3. Turn out a lock bolt between a wing and a bumper, disconnect and remove a bracket as it is described in the Section Removal and installation of a bumper.
4. Turn out bolts of fastening and remove an expansion clip of a cover of the bottom, and also facing of a longitudinal beam around a wing.
5. Disconnect by means of a plastic wedge an entrance level of doors from the holder of a clip and remove.

6. Enter a plastic wedge into a gap between a wing (1) and facing of a longitudinal beam (2) and take out facing from two holders of clips (the shooter on an illustration).

7. Turn off 2 nuts (3) fastenings of a wing.
8. Open a cowl and establish it vertically.

9. Turn out bolts (1) and remove a wing (2).

10. Disconnect a cover (3) and the sealing film (4).


Installation

 PERFORMANCE ORDER

1. Installation is carried out in the sequence, the return to removal.
At the same time you watch correctness of closing of a cowl, and also a gap in relation to a forward door and a cowl. Value of a gap is given in Specifications.
2. Establish into place a forward wheel so that the marks put at removal coincided. Previously grease with a thin layer of bearing lubricant the aligning wheel disk belt on a nave. Do not grease bolts of fastening of a wheel. Replace rusty bolts. Wrap bolts. Lower the car on wheels and tighten bolts cross-wise the moment of 110 Nanometers.