Mercedes-Benz
+ Mercedes-Benz cars of class C (W-203)
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
- Automatic transmission
Specifications
+ The automated box of gear shifting 716.6
- Automatic transmission 722.6
Search of malfunctions - the general information
Problems of the block of electronic control and the operating signals
Removal and the AT installation with the hydrotransformer
The AT electrohydraulic control unit (AT is established)
Dismantling and assembly of the electrohydraulic control unit
Dismantling and assembly of a plate of gear shifting
Case of transmission and hydrotransformer
Multidisk brakes of B2, B3 and gear wheel of blocking at "Parking"
Dismantling and assembly of a back hollow shaft with the back coupling of a free wheeling
Removal and installation of a multidisk brake B1 and oil pump
Dismantling and assembly of the oil pump
Dismantling and assembly of a multidisk brake of B1
Dismantling and assembly of a multidisk brake of B2
Dismantling and assembly of an output shaft with the central and back block of planetary gear wheels
Removal and installation of multidisk couplings K1, K2 and K3
Dismantling and assembly of coupling of K1
Dismantling and assembly of the leading shaft with coupling by K2 and the forward block of planetary gear wheels
Dismantling and assembly of coupling of K3
The blocking mechanism at "parking"
Removal and installation of the lever of the selector of gear shifting
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Dismantling and assembly of a multidisk brake of B2
Dismantling and assembly of a multidisk brake of B2
|
|
14a — the External support of a brake B2 or the B3 piston
14b-d — Sealing rings of a brake of B3
27 — B2 brake Piston
28 — the Directing piston ring
28a-b — Sealing rings on the directing piston ring
29, 134b — Disk springs |
30 — the Spring plate
31, 134a — Lock rings
32 — the Guide of the piston of a brake of B2 and B3
32a — the Sealing ring
134 — the Block of disks |
Dismantling and assembly of a multidisk brake of B2
|
|
| 31 — the Lock ring |
074 — the Stripper |
Dismantling and assembly of a multidisk brake of B2
|
|
27 — the Piston
28 — the Directing piston ring |
137 — the Valve |
Dismantling and assembly of a multidisk brake of B2
|
|
And — the Oil channel of the B3 piston
In — the Oil channel of the B2 piston from a reverse side |
With — the Oil channel of coupling K3
D — the Oil channel of the B2 piston from gear shifting |
Assembly of a guide of the piston and external support of a multidisk brake B2
|
|
2 — the transmission Case
14a — the External support of a brake B2, (B3 piston) |
32 — a piston Guide |
B1 brake section
|
|
14a — the External support of a brake B2
27 — the B2 Piston
134a — the External disk (thickness of 6.5 mm)
134b — the External disk (thickness of 1.8 mm) |
134s — the External disk (thickness of 1.8 mm)
134d — Frictional disks
134e — the Disk spring
144a — the Lock ring
L — the Gap |
Dismantling
|
|
| 1. Remove a lock ring (134a).
| Parameters
|
| Gap in a mnogodiskovmtormoza of B1, mm |
Disk 2 |
1,90-2,30 |
Disk 3 |
2,00-2,40 |
Disk 4 |
3,00-3,40 |
2. Remove the block of disks of a brake B2 (134) and a disk spring (134b) from an external support of a brake B2.
3. Establish a stripper (074) on a disk spring (29) and squeeze it until the groove for a lock ring is not released.
4. Remove a lock ring (31).
5. Remove a spring plate (30) and a disk spring (29).
6. Disconnect the directing ring (28) of the piston and the piston of a brake B2 (27) from the B3 piston (14a), having given compressed air to an opening of D (address an accompanying illustration).
7. Press the directing ring (28) from the B2 (27) piston.
8. Remove a guide (32) from the B3 piston (14a), having given compressed air to an opening And. |
|
Assembly
|
|
| 1. Establish a guide (32) and the B3 piston (14a) in the correct situation. For this purpose, insert a guide (32) into the case of transmission (2) and tighten. Press an external support of a brake B2 (14a) against the stop in a guide (32). Bore on vents or a cut on an external support of a brake B2 (14a) have to be directed (arrow) down.
2. Insert the piston of a brake B2 (27) into B3 brake piston (14a). The rounded-off ends of sealing rings (14s), (28a) and (28b) have to be directed outside the Rounded-off end of a sealing ring (14d) has to be directed in inside (address an accompanying illustration 17.1).
3. Insert the directing ring (28) of the piston. The valve (137) in the directing ring of the piston has to be from above.
4. Insert a disk spring (29) and a spring plate (30).
5. Establish a stripper (074) on a disk spring (29) and squeeze it until the groove for a lock ring is not released.
6. Insert a lock ring (31).
7. Insert a disk spring (134b) and the block of disks (134) on an external support of a brake B2.
8. Establish B3 brake disks together in the order presented on an illustration (109) and insert them in turn.
9. Install a press (078) on an external drive (70s).
10. Squeeze the block of disks by means of a press against the stop until the otmetochny ring is visible (a small arrow).
11. Measure a gap of L in three points between a lock ring (144a) and an external disk (134a). The size of gaps in a multidisk brake (B2) are provided in the table.
Parameters |
| Gap in a multidisk brake of B2, mm |
Disk 4 |
1.90-2.30 |
Disk 5 |
2.00-2.40 |
12. Adjust a gap a lock ring (144a) if it is necessary. Thickness of a lock ring: 2.9, 3.2, 3.5, 3.8 and 4.1 mm.
13. Establish a lock ring (134a). |
|
|
|